This one links to gear. Gear links may be affiliate links (Amazon); if you buy through one we may earn a small commission at no cost to you. We only list what we'd buy again. Details.
Seasoning is not a coating you paint on. It is oil that has been heated past its smoke point until it breaks down and bonds to the iron as a hard, dark polymer. Thin layers bond. Thick layers stay gummy, flake, and convince people cast iron is hard to own.
It isn’t. It’s about four hours of mostly waiting, done right once, and then three small habits forever.
12-inch Cast Iron Skillet
The last pan you'll buy. Comes pre-seasoned from the factory, which is a start, not a finish.
1. Strip it if it needs stripping
A new skillet comes pre-seasoned and can skip this step. A thrift-store pan with rust or a sticky, uneven surface cannot.
Scrub it with steel wool and dish soap until you see bare gray metal. Rust comes off with a 50/50 vinegar and water soak for no more than an hour; longer and the vinegar starts eating good iron. Rinse, dry immediately, and go straight to step 2. Bare iron rusts in minutes in July humidity.
2. Dry it hot
Put the pan on a burner over medium heat for 5 minutes, or in a 200-degree oven for 15. You want every bit of water gone, including from the pores of the metal you can’t see. A warm pan also takes oil more evenly than a cold one.
3. Oil it, then wipe almost all of it off
This is the step everyone gets wrong.
Pour in about a teaspoon of oil. Rub it over every surface with a lint-free rag: inside, outside, handle, bottom. Then take a clean rag and wipe it all off. Keep wiping until the pan looks dry and barely shines. It will feel like you removed everything. You didn’t. There is a film left behind a few molecules thick, and that is the correct amount.
4. Bake it upside down, hot, for an hour
Oven to 450 to 500 degrees, above the oil’s smoke point. Put the pan upside down on the middle rack so nothing pools in the bottom. Put foil or a sheet pan on the rack below to catch drips. One hour.
Turn the oven off and leave the pan inside until it’s cool enough to touch, about 45 minutes. Pulling it out hot can shock a fresh layer.
Expect smoke. Open a window, run the vent, do this in the evening when the kitchen is already hot anyway.
5. Do it again. Then twice more.
One layer is a start. Four thin layers is a seasoning. Repeat steps 3 and 4 three more times. The pan will go from gray-brown to a dull, even black.
Total time is about four hours. Active time is about ten minutes. Watch a game.
6. Keep it seasoned
This is the part the pan actually cares about.
Cook fat in it. Bacon, burgers, cornbread, anything with oil. Every hot, fatty meal adds a micro-layer. A skillet used four times a week gets better every month without you doing anything.
Clean it right. Hot water, a little dish soap if you want, and a scrubber that won’t cut the seasoning. Modern dish soap won’t strip seasoning; that advice dates from lye soap. What strips it is soaking, the dishwasher, and steel wool.
Chainmail Cast Iron Scrubber
Takes off stuck food without taking off seasoning. Replaces the steel wool you were about to ruin the pan with.
Dry it on the burner. Towel it, then put it on medium heat for 2 minutes until it’s bone dry. Rub in a few drops of oil while it’s warm, wipe off the excess, put it away.
When it goes wrong anyway
A spot of rust: scrub it off with the chainmail and a little oil, then do one round of steps 3 and 4. Flaking: the layer underneath was too thick. Scrub the flakes off, re-season two coats. A sticky patch: not enough heat or too much oil. Bake it empty at 500 for an hour.
None of these is a dead pan. Cast iron can be brought back from a barn.
The short version
Thin oil, wipe it nearly off, 500 degrees upside down for an hour, four times. Cook fat in it, don’t soak it, dry it on the burner. Done right once, it’s done for the rest of your life.